How to Install a Bidet
|
|
Posted On :
Apr-23-2010
| seen (646) times |
Article Word Count :
913
|
|
This article will walk you through how to install a bidet attachment to your existing toilet.
|
|
Electronic bidet installation is actually quite easy, requiring no special skills at all. These seats are designed for “Do It Yourself” (DIY) installation. This article will walk you through how to install a bidet attachment to your existing toilet. Note: If you need help installing a basin-type bidet, which are separate porcelain fixtures that sit next to the toilet, please contact your local plumber. Basin-type bidets may require additional plumbing and a new drainage system.
Modern electronic bidets are easy to install because they tap in to the existing cold water valve which refills your toilet’s water tank. Moreover, you don’t need a separate drainage system since the bidet’s water just falls into the toilet bowl.
There are three main components to electronic bidet installation – (1) taking some measurements of your existing toilet to ensure proper fit prior to ordering, (2) mounting the bidet onto your toilet and (3) connecting your bidet to the existing cold water supply.
We’ll explain each of these three components in detail below. Alternatively, if you’d like to see bidet installation in action, you can watch this How to Install a Bidet video: youtube.com/watch?v=NGJ6ZNGM11Y
- Measurement: Bidet measurements vary by model, so it’s important you refer to the product specifications for the model you’re interested in. But here are some general guidelines to get you started.
The first and most important measurement is the measurement in the back, where the rear of the bidet will sit. You’ll notice two caps behind your existing seat, and beneath these caps are bolts which secure the toilet seat to the toilet. Measure the clearance from your water tank to the center of these caps. Most bidets require at least 1.5 inches of clearance from the front of the water tank to the center of these caps. If your tank is curved, you’ll need to take that into account by measuring from the point of the water tank closest to the caps. Make sure you have at least 1.5 inches of clearance all the way across the back. More than 1.5 inches is okay, as long as it’s not less.
The second measurement is the width between the caps behind your existing seat. In other words, how far apart are the caps from each other? You’ll want at least 5.5 inches in width between the center of the caps. Again, more than 5.5 inches is okay, as long as it’s not less.
If you have at least 1.5 inches of clearance in the back, and at least 5.5 inches of width between the caps, then congratulations – most electronic bidets are compatible with your toilet. Now we just have to determine which type of seat your bidet will come with – an elongated or round seat. Take one more measurement to determine the length of your toilet bowl. Start from the caps behind your existing seat and measure towards the front of the bowl. Elongated seats typically measure 18 inches to 19.5 inches, while round seats typically measure 16.5 inches to 18 inches.
- Mounting: Now that you have properly measured your toilet and ordered the correct seat-type, it’s time to mount the bidet. In the box your bidet came in, all parts needed for installation will be included. One of these parts is the mounting bracket, which is used to attach your bidet to the toilet.
Go ahead and remove your existing toilet seat by unscrewing the bolts behind the seat. After removing your seat, you’ll see the two holes which will be used to secure your mounting bracket. Place the mounting bracket on top of these two holes, and then secure the bracket with the nuts and bolts which came with your bidet.
Once the mounting bracket is secured to your toilet, the bidet slides on to the bracket and attaches to your toilet. On most bidet models, you’ll hear an audible “click” which lets you know when the bidet is properly fastened.
- Connecting to Water Supply: Behind your toilet you’ll find a water valve, with a hose connecting to the bottom of the water tank. First, turn off the water intake by closing the valve. This stops the water, preventing it from passing on through to the hose. Then unscrew the hose from the water valve. Again, make sure you’ve closed the valve first or else you’re gonna get wet!
Now, find the metal T-connection which came with your shipment and fasten it to the valve. It’s called a T-connection because it’s shaped like the letter “T” and allows the water to run two different ways – one way will be back to your water tank, and the other way will be to the bidet.
Once the T-Connection has been secured to the water valve, reconnect the hose to your water tank by securing it to the top end of the T-connection. Secure a second hose (also included with your shipment) to the other opening of the T-connection. Connect the other end of this hose to your bidet. Use a wrench to tighten all connections. Turn the water supply back on, and check for leaks. Congratulations on learning how to install a bidet!
|
|
|
|
Article Source :
http://www.articleseen.com/Article_How to Install a Bidet_16976.aspx
|
|
Author Resource :
About the Author: Jensen Lee is the founder of bidetsPLUS, an online presence specializing in the modern electronic bidet. bidetsPLUS provides its users with an array of educational content on the bidet, including video presentations, bidet reviews, and also carries a wide range of bidet products. Visit us at www.bidetsplus.com
|
|
Keywords :
bidet, toilet seat, electronic bidet, japanese toilet, bidets, washlet, toilet,
Category :
Home and Family
:
Home Improvement
|
|
|
|
