How to Fix Hot Water Leak Perth?

Author Information

Aaron Pascoe has 1 Published Articles

Australia,
WA,
Willetton,
Pascoes Gas and Hot water,
PO Box 421

How to Fix Hot Water Leak Perth?

Posted On : Feb-14-2013 | seen (728) times | Article Word Count : 411 |

If you are at home in Perth and are experiencing a hot water leak from your geyser, it’s time to give it a fix. You need to check out certain things to fix hot water leak Perth. The problem is almost always among the following 4 things:

- It is Not a Leak: People often assume that the water that collects on the floor around the heater is a result of a leak. The reality is that it is not at all a leak, but merely condensation building up around the tank as it holds the hot water.

- Drain Valve: Fixing the leak is often as simple as tightening the drain valve. If you think that the drain valve is faulty, attach it tightly with a screw with the help of a wrench. Tightening the hand is generally good, but at times it might be needed to be tightened a little more.

- Tank: The tank has a limited lifespan. The corrosion resistance of the unit depends on its cost. There is water in the tank all the time and this makes it likely to rust and corrode. If the tank does not serve any use, it is best to have it replaced. This will be less expensive.

- Pipes: If the hot water leak Perth is from the pipes, you need to find the fitting from which water is leaking, and have it tightened. Make sure not to over tighten the fixture. If the leak is thus not repaired, you must purchase a new fitting which is easy to install.

If the dripping geyser is overflowing, it is a normal thing and you need not be tensed because this is caused due to the heating and cooling of the geyser. If the quantity of water that drips exceeds a few liters a day, you need to check the pressure control valve. If the drip is constant, have the valve replaced altogether. Occasional dripping from the geyser is okay.

Another problem is overheating. You tend to see hot water or steam escaping from the overflow. If the thermostat faults in the off or open position, there will not be any heating. If the thermostat faults in the on position, the water may boil and lead to an explosion. This is often caused by a faulty thermostat, in which case, it would be best to switch off the geyser instantly and call a plumber.

Re-Publish this Article

<h1>How to Fix Hot Water Leak Perth?</h1> Author: <a href='http://www.articleseen.com/profile_Aaron Pascoe.aspx'>Aaron Pascoe</a> If you are at home in Perth and are experiencing a hot water leak from your geyser, it’s time to give it a fix. You need to check out certain things to fix hot water leak Perth. The problem is almost always among the following 4 things:

- It is Not a Leak: People often assume that the water that collects on the floor around the heater is a result of a leak. The reality is that it is not at all a leak, but merely condensation building up around the tank as it holds the hot water.

- Drain Valve: Fixing the leak is often as simple as tightening the drain valve. If you think that the drain valve is faulty, attach it tightly with a screw with the help of a wrench. Tightening the hand is generally good, but at times it might be needed to be tightened a little more.

- Tank: The tank has a limited lifespan. The corrosion resistance of the unit depends on its cost. There is water in the tank all the time and this makes it likely to rust and corrode. If the tank does not serve any use, it is best to have it replaced. This will be less expensive.

- Pipes: If the hot water leak Perth is from the pipes, you need to find the fitting from which water is leaking, and have it tightened. Make sure not to over tighten the fixture. If the leak is thus not repaired, you must purchase a new fitting which is easy to install.

If the dripping geyser is overflowing, it is a normal thing and you need not be tensed because this is caused due to the heating and cooling of the geyser. If the quantity of water that drips exceeds a few liters a day, you need to check the pressure control valve. If the drip is constant, have the valve replaced altogether. Occasional dripping from the geyser is okay.

Another problem is overheating. You tend to see hot water or steam escaping from the overflow. If the thermostat faults in the off or open position, there will not be any heating. If the thermostat faults in the on position, the water may boil and lead to an explosion. This is often caused by a faulty thermostat, in which case, it would be best to switch off the geyser instantly and call a plumber. About the Author: There are a number of things you can do to <a rel="nofollow" href="http://www.pascoesgasandwater.com.au/">fix hot water leak Perth</a>. However, most commonly, you need to call a plumber to correct the <a rel="nofollow" href="http://www.pascoesgasandwater.com.au/">hot water leak Perth</a>. Article Source: <a href='http://www.articleseen.com/Article_How-to-Fix-Hot-Water-Leak-Perth_250976.aspx'> http://www.articleseen.com/Article_How to Fix Hot Water Leak Perth?_250976.aspx</a>

Article Source : http://www.articleseen.com/Article_How to Fix Hot Water Leak Perth?_250976.aspx

Author Resource :
There are a number of things you can do to fix hot water leak Perth. However, most commonly, you need to call a plumber to correct the hot water leak Perth.

Keywords : hot water leak Perth, fix hot water leak Perth,

Category : Home and Family : Home Improvement

Print this Article Send to Friend